Determine your magnetic zone by referring to the zone map. Signal mirrors if equipped When the turn signal is activated, the lower portion of the mirror. Disassemble the tools and snap them back into the tool tray. After approximately 10 minutes of rear defrost operation, the climate control system will automatically disable the rear defrost operation. Press again to disable scan and remain on the current station.
Correct fluid level The transmission fluid should be checked at normal operating temperature 66°C-77°C 150°F-170°F on a level surface. Do not attempt to service, repair or modify the system. Do not hang any type of accessory or accessory bracket from the plug. Refer to Rear seats in the Seating and safety restraints chapter. The Safety Canopy could injure you as it deploys from the headliner.
Refer to the Warning Light section in the Instrument Cluster chapter. Allow the belt to retract. Tachometer Indicates the engine speed in revolutions per minute. Under no circumstance should these limitations be exceeded. Refer to the Safety belt maintenance section in this chapter. Lay the tire on the ground, near the rear of the vehicle, with the valve stem side facing up. Turn all other accessories off.
When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the front disc brake hub and rotor that contacts the wheel. Put the indicator back in and ensure it is fully seated. Selecting Route Criteria Once you have selected a destination, select from the following route criteria: 1. Put the indicator back in and ensure it is fully seated. Chilton's Ford Expedition repair manuals include diagrams, photos, and instructions you need to assist you in do-it-yourself Expedition repairs. Instead, spray onto a soft cloth and gently wipe the unit.
Lift and pull the seat rearward until the latch is engaged. On vehicles equipped with air suspension, turn the air suspension and the ignition switch off prior to jacking, hoisting or towing your vehicle. You can use either code to unlock your vehicle. Press and hold the button to reset. To access this information, special equipment must be directly connected to the recording modules.
To prevent the vehicle from moving when you change the tire, be sure that the parking brake is set and the diagonally opposite wheel is blocked. Route the child safety seat tether strap under the head restraint outboard seats and over the back of the seat. Remove and replace the bulb. Each time the vehicle is started, the transmission will automatically return to normal overdrive mode. Buckle then unbuckle the safety belt three times, ending with the safety belt unbuckled. Refer to the Safety belt maintenance section in this chapter. Make the final connection of the negative - cable to the jump starting stud located in the rear of the engine compartment, near the battery.
Locate the anchor webbing loop for the seating position. Running out of fuel Avoid running out of fuel because this situation may have an adverse affect on powertrain components. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. Whenever coolant has been added, the coolant level in the coolant reservoir should be checked the next few times you drive the vehicle. Make the final connection of the negative - cable to the jump starting stud located in the rear of the engine compartment, near the battery. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is pulled out and a click is heard.
The red indicator light will flash slowly and then rapidly after HomeLink accepts the radio frequency signal. See your Ford or Lincoln Mercury dealer. A correct zone setting will eliminate this error. Anti-scan feature The anti-scan feature prevents repeated attempts at arriving at a valid key code. Locate the handle on the side of the seat, lifting it to release the seatback. The levels will be shown in the display. Connect the positive + jumper cable to the positive + terminal of the discharged battery.
See your Ford or Lincoln Mercury dealer. Attach the trailer to the vehicle and adjust the hitch equalizers so that the front bumper height is within 0—13 mm 0. Start the engine and let it run until it reaches normal operating. Turn all other accessories off. If a light fails to illuminate, have the vehicle serviced. Third row seating position 1. Ford may change the contents without notice and without incurring obligation.
If the safety seat is not anchored properly, the risk of a child being injured in a crash greatly increases. Your vehicle may be higher to allow it to travel over rough terrain without getting hung up or damaging underbody components. For assistance, refer to the label located on the side of the seat cushion. Only recommended products should be used. Refer to the scheduled maintenance guide for the service interval schedules. On vehicles equipped with air suspension, turn the air suspension and the ignition switch off prior to jacking, hoisting or towing your vehicle.