Reverse order when done replacing … light bulb H4. To install a bulb, align the tabs of the bulb socket with the cutouts of the mounting hole. You really can't hurt it. Depending on wether you talking about the light bulb retainer of the head light assembly to include the lens you probably need to remove the air filter box on one side and possibly the battery on the other. With the bulb and connection made replace the assembly back in the location behind the head light assembly. Step3 Locate the back of the headlight assembly and determine whether the low- or high-beam bul … b needs to be replaced.
Step4 Turn the headlight bulb socket counterclockwise to remove it from the assembly. Take the new handle and place the balls of the wires into the holders of the new handle. Turn the bulb and remove it. The head lamp bulb is held in either by a rubber boot with a metal wire that you pinch to re … lease or a twist off. To replace the thermostat in a 2002 Toyota Camry the vehiclebattery must be disconnected and the engine coolant must bedrained.
Unplug the connector while depressing the lock release. It then should come right out. Do not pry at the black clips at the top of the panel, you will break them if you do - they act as a kind of hanger clip. Theres a white or red piece of plastic behind the headlight you have to open hood and reach your hand in behind headlight that holds the light in and is also the electrical connector. Carefully take note of how there are two wires with metal balls on their ends one has a white plastic casing while the other has a green casing.
It is possible that there is either corrosion in the plug, or the wires are connecting somewhere. Twist it clockwise to secure its position. You will also need on Phillips head screw driver. Test the new headlight to make sure it works before closing the hood. Now put everything back where it was when you began. Remove the black triangular cover located above the upper hinge of the door. The new housing unit c … an now beattached along with the parts taken off.
Who had some ideas about this? Close the hood and test the bulb replacement. Remove the rubber stopper from the back of the headlight housing by pullin gon the tab. Do Not Move the adjusting screws on the new assembly as the should be preset. At AutoZone, we want to make sure you always drive safely, which means ensuring that your lights are as bright and visible as possible. Step5 Unplug the electrical connector from the back of the bulb.
I just replaced mine today and it was actually easy, but there are a lot of screws to take out. Turn the plastice device to unlock it and pull back. There is a screw on the right hand side that you take off and pull the compartment down. It may be time to replace your headlight lenses if they are malfunctioning or are broken, cracked, foggy or cloudy. Carefully trying not to break it - take off the plastic plate that lies within the door handle casing - it is covering another screw that you need to remove. Step1 Shut off the Camry's engine and set the parking brake for added safety.
Carefully trying not to break it - take off the plastic plate that lies within the door handle casing - it is covering another screw that you need to remove. It is really tight in there. Carefully place all of these screws in a safe place where you will not lose them. Recommend that you replace in pairs as I have always found that when you have one burn out, its corresponding light on the other side probably will not be far behind. Sorry, the … Gen I Solara doesn't have a cabin air filter.
Install the new bulb and install the connector. Ready to dutifully serve you on your commute or on a cross-country journey, your Camry is primed for any sort of trip. Do not pry at the black clips at the top of the panel, you will break them if you do - they act as a kind of hanger clip. The door panel should now be free from the door. Carefully take note of how there are two wires with metal balls on their ends one has a white plastic casing while the other has a green casing. It is not rocket science.
Take the door upholstery remover and place it under the edge of the door upholstery panel and insert inot the fastener as far as possible. I don't think there was too much difference between the headlight-changing process of the 93 and the 94. It is just a plug in pull out connection. Also, make sure its headlights are switched off. Remove the bulb from the socket, put the new bulb in the socket.